Creality CR10S - Revision history

Blu: /* Operators' Log */ new section summarizing five months of serious changes

2025-09-09T08:48:55Z

Operators' Log: new section summarizing five months of serious changes

← Older revision		Revision as of 08:48, 9 September 2025
Line 171:		Line 171:

	The 24v dual ball-bearing fan was replaced with a 12v sunon fan from the stockpile.		The 24v dual ball-bearing fan was replaced with a 12v sunon fan from the stockpile.

			==== 2025-09-09 [[User:Blu \| Brandon]] ====
			There have been a lot of changes to the printer. The entire hot end assembly is replaced with a [https://www.thingiverse.com/thing:4561720 QED Hot End System] with direct drive and a v6 clone.

			Additionally, a Z synchronization system was added and the firmware was recompiled with a version that supports input shaping.

	== Other 3D Printers ==		== Other 3D Printers ==

Blu: /* 2025-04-06 Brandon */

2025-04-07T08:44:17Z

2025-04-06 Brandon

← Older revision		Revision as of 08:44, 7 April 2025
Line 169:		Line 169:
	==== 2025-04-06 [[User:Blu \| Brandon]] ====		==== 2025-04-06 [[User:Blu \| Brandon]] ====
	The YS-Tech fan was replaced with a 24v dual ball-bearing fan purchased from Ali.		The YS-Tech fan was replaced with a 24v dual ball-bearing fan purchased from Ali.

			The 24v dual ball-bearing fan was replaced with a 12v sunon fan from the stockpile.

	== Other 3D Printers ==		== Other 3D Printers ==

Blu: /* Operators' Log */

2025-04-07T00:13:09Z

Operators' Log

← Older revision		Revision as of 00:13, 7 April 2025
Line 166:		Line 166:
	\| Walls \|\| Z seam Alignment \|\| Shortest		\| Walls \|\| Z seam Alignment \|\| Shortest
	\|}		\|}

			==== 2025-04-06 [[User:Blu \| Brandon]] ====
			The YS-Tech fan was replaced with a 24v dual ball-bearing fan purchased from Ali.

	== Other 3D Printers ==		== Other 3D Printers ==

Blu: added printer start script

2024-03-17T19:22:32Z

added printer start script

@@ Line 27: / Line 27: @@
 == Description ==
 The Creality CR-10S V1 is a cartesian 3d printer with a relatively large build volume.  It is built primarily using 4040 and 4080 extruded aluminum with the beams running on the X axis being constructed of 4040 aluminum and all other beams being constructed of 4080 aluminum.  The axes on the CR-10S are constructed using shielded bearings and acetal running wheels which provide maintenance free operation.  The axes are constructed in a Prusa format with the Y axis moving the build plate, the X axis moving the extruder, and the Z axis moving the X axis carriage.
 == Firmware ==

Blu at 09:31, 12 May 2023

2023-05-12T09:31:07Z

← Older revision		Revision as of 09:31, 12 May 2023
Line 146:		Line 146:
	This is a part of our ongoing effort to document our 3D printers.		This is a part of our ongoing effort to document our 3D printers.
	{{Template:3D_DigitalFabrication}}		{{Template:3D_DigitalFabrication}}
	[[Category:3D ~~Printers~~]]		[[Category:3D Printing]]

Blu: /* 2023-04-01 Brandon */

2023-04-04T07:49:16Z

2023-04-01 Brandon

← Older revision		Revision as of 07:49, 4 April 2023
Line 108:		Line 108:

	==== 2023-04-01 [[User:Blu \| Brandon ]] ====		==== 2023-04-01 [[User:Blu \| Brandon ]] ====
	Printing with PETG led to strange inconsistencies that may be related to hydrated filament. These largely interfered with		Printing with PETG led to strange inconsistencies that may be related to hydrated filament. These largely interfered with the attempted transparent printing.

	It is noted that a comprehensive list of changed settings has not been posted to the wiki. This section aims to fix that deficiency. The following settings are applied to the printer:		It is noted that a comprehensive list of changed settings has not been posted to the wiki. This section aims to fix that deficiency. The following settings are applied to the printer:
Line 122:		Line 122:
	\|rowspan=2\| Speed \|\| Initial Layer Speed \|\| 12 mm/s		\|rowspan=2\| Speed \|\| Initial Layer Speed \|\| 12 mm/s
	\|-		\|-
	\| Enable Acceleration Control \| ✅		\| Enable Acceleration Control \|\| ✅
	\|-		\|-
	\|rowspan=6\| Travel \|\| Retraction Distance \|\| 4.0 mm		\|rowspan=6\| Travel \|\| Retraction Distance \|\| 4.0 mm

Blu: /* Operators' Log */ Added operator log and some settings

2023-04-04T07:43:57Z

Operators' Log: Added operator log and some settings

← Older revision		Revision as of 07:43, 4 April 2023
Line 106:		Line 106:

	The printer also experienced a collision with the cables connecting to the X axis carriage and this caused the carriage to become un-level. The carriage and bed were leveled and the printer was tested with YACS again.		The printer also experienced a collision with the cables connecting to the X axis carriage and this caused the carriage to become un-level. The carriage and bed were leveled and the printer was tested with YACS again.

			==== 2023-04-01 [[User:Blu \| Brandon ]] ====
			Printing with PETG led to strange inconsistencies that may be related to hydrated filament. These largely interfered with

			It is noted that a comprehensive list of changed settings has not been posted to the wiki. This section aims to fix that deficiency. The following settings are applied to the printer:
			{\| class="wikitable"
			! \| Section \|\| Setting \|\| Value
			\|-
			\|rowspan=2\| Quality \|\| Initial Layer Height \|\| 0.3 mm
			\|-
			\| Initial Layer Line Width \|\| 150 %
			\|-
			\| Material \|\| Initial Layer Flow \|\| 105 %
			\|-
			\|rowspan=2\| Speed \|\| Initial Layer Speed \|\| 12 mm/s
			\|-
			\| Enable Acceleration Control \| ✅
			\|-
			\|rowspan=6\| Travel \|\| Retraction Distance \|\| 4.0 mm
			\|-
			\| Retraction Speed \|\| 60 mm/s
			\|-
			\| Retraction Minimum Travel \|\| 1.0 mm
			\|-
			\| Combing Mode \|\| Not on Outer Surface
			\|-
			\| Z hop when Retracted \|\| ✅
			\|-
			\| Z hop Height \|\| 0.4 mm
			\|-
			\|rowspan=2\| Build Plate Adhesion \|\| Build Plate Adhesion Type \|\| Brim
			\|-
			\| Brim Width \|\| 4.0 mm
			\|-
			\| Walls \|\| Z seam Alignment \|\| Shortest
			\|}

	== Other 3D Printers ==		== Other 3D Printers ==

Blu: /* Operators' Log */

2023-03-13T09:25:16Z

Operators' Log

← Older revision		Revision as of 09:25, 13 March 2023
Line 101:		Line 101:
	==== 2023-01-10 [[User:Blu \| Brandon]] ====		==== 2023-01-10 [[User:Blu \| Brandon]] ====
	"Travel :: Extrusion Combing" turned off in Cura; it should have been on the entire time. This setting was changed to "Not on outer surface."		"Travel :: Extrusion Combing" turned off in Cura; it should have been on the entire time. This setting was changed to "Not on outer surface."

			==== 2023-03-09 [[User:Blu \| BLu ]] ====
			YACS printing was successfully completed on this printer. It is recommended that the fan speed be adjusted since the printer exhibited print curl during YACS printing.

			The printer also experienced a collision with the cables connecting to the X axis carriage and this caused the carriage to become un-level. The carriage and bed were leveled and the printer was tested with YACS again.

	== Other 3D Printers ==		== Other 3D Printers ==

Blu: /* Operators' Log */

2023-01-18T09:52:12Z

Operators' Log

← Older revision		Revision as of 09:52, 18 January 2023
Line 98:		Line 98:
	==== 2023-01-05 [[User:Blu \| Brandon]] ====		==== 2023-01-05 [[User:Blu \| Brandon]] ====
	Print completed without note.		Print completed without note.

			==== 2023-01-10 [[User:Blu \| Brandon]] ====
			"Travel :: Extrusion Combing" turned off in Cura; it should have been on the entire time. This setting was changed to "Not on outer surface."

	== Other 3D Printers ==		== Other 3D Printers ==

Blu: /* Operators' Log */

2023-01-06T20:14:13Z

Operators' Log

← Older revision		Revision as of 20:14, 6 January 2023
Line 95:		Line 95:

	The printer successfully printed the camera angler upgrade for itself on the same day, and the printer was removed from stale status.		The printer successfully printed the camera angler upgrade for itself on the same day, and the printer was removed from stale status.

			==== 2023-01-05 [[User:Blu \| Brandon]] ====
			Print completed without note.

	== Other 3D Printers ==		== Other 3D Printers ==