BLu Delta 3D Printer - Revision history

KevinYang: Redirected page to Kossel Delta 3D Printer

2020-07-26T06:06:55Z

Redirected page to Kossel Delta 3D Printer

← Older revision		Revision as of 06:06, 26 July 2020
Line 1:		Line 1:
	~~'''BLu Delta''' is a RepRap Kossel made by Brandon Lu.~~		#REDIRECT [[Kossel_Delta_3D_Printer]]

	~~== General Advice and Precautions ==~~
	~~It is by no means safe to operate this delta if the user wishes to consider himself a sane and rational human being.~~

	~~Operating this delta would create a situation in which the user ceases to be a sane and rational human being. The user may become a robot. Or you may lose your sanity.~~

	~~Either way, ask before using. The last time somebody used without asking, the extruder was clogged and needed to be unclogged through a two-hour process.~~

	~~=== Precautions ===~~
	Do not let the extruder heat up without a powered fan. The recommended fan setting is always above 20%. The printer accepts fan commands in pulse-width-modulated counts ranging from 0 to 255. Always set the printer to a count of 51 or more counts when the extruder is heated up or it is expected to heat up.

	~~== Configuration ==~~
	~~TODO~~

	~~=== Slic3r ===~~
	~~TODO~~

	~~=== Cura ===~~
	~~TODO~~

	~~== Materials ==~~
	~~=== ABS ===~~
	~~TODO~~
	~~=== PLA ===~~
	~~TODO~~
	~~=== TPE / TPC ===~~
	~~Flexible filaments will not work reliably with BLu printer since the printer has a bowden-tube extruder.~~

	~~== History ==~~
	~~=== Head clogs ===~~
	~~The printer has been clogged at least five times. Every clog was because of incorrect heat application and has required specialty repairs.~~

	~~== Lending Terms ==~~
	~~BLu Delta is currently on loan from~~ [[~~User:BLu~~]]~~, hereinafter referred to as "owner."~~

	~~Any member or visitor of MAG Laboratory, heinafter referred to as "user," '''''may''''' use the printer given the included configurations and with modifications of these printer configurations.~~
	~~Users excluding qualified 3d printer maintainers as defined by the owner '''''shall not''''' attempt alterations or repairs on the printer.~~
	~~Users excluding qualified 3d printer maintainers as defined by the owner '''''shall not''''' attempt to change filament on the printer. (Soon to change)~~

Blu at 03:39, 20 September 2018

2018-09-20T03:39:44Z

← Older revision		Revision as of 03:39, 20 September 2018
Line 21:		Line 21:

	== Materials ==		== Materials ==
			=== ABS ===
			TODO
			=== PLA ===
			TODO
			=== TPE / TPC ===
			Flexible filaments will not work reliably with BLu printer since the printer has a bowden-tube extruder.

	== History ==		== History ==
	=== Head clogs ===		=== Head clogs ===
	The printer has been clogged at least five times. Every clog was because of incorrect heat application and has required specialty repairs.		The printer has been clogged at least five times. Every clog was because of incorrect heat application and has required specialty repairs.

			== Lending Terms ==
			BLu Delta is currently on loan from [[User:BLu]], hereinafter referred to as "owner."

			Any member or visitor of MAG Laboratory, heinafter referred to as "user," '''''may''''' use the printer given the included configurations and with modifications of these printer configurations.
			Users excluding qualified 3d printer maintainers as defined by the owner '''''shall not''''' attempt alterations or repairs on the printer.
			Users excluding qualified 3d printer maintainers as defined by the owner '''''shall not''''' attempt to change filament on the printer. (Soon to change)

Blu at 20:03, 10 September 2018

2018-09-10T20:03:15Z

← Older revision		Revision as of 20:03, 10 September 2018
Line 9:		Line 9:

	=== Precautions ===		=== Precautions ===
	Do not let the extruder heat up without a powered fan. The recommended fan setting is always above 20%. The printer ~~gives~~ fan commands in pulse-width-modulated counts ranging from 0 to 255. Always set the printer to a count of 51 or more counts when the extruder is heated up or it is expected to heat up.		Do not let the extruder heat up without a powered fan. The recommended fan setting is always above 20%. The printer accepts fan commands in pulse-width-modulated counts ranging from 0 to 255. Always set the printer to a count of 51 or more counts when the extruder is heated up or it is expected to heat up.

	== Configuration ==		== Configuration ==

Blu at 20:02, 10 September 2018

2018-09-10T20:02:51Z

← Older revision		Revision as of 20:02, 10 September 2018
Line 9:		Line 9:

	=== Precautions ===		=== Precautions ===
	Do not let the extruder heat up without a powered fan. The recommended fan setting is always above 20%. The printer gives fan commands in pulse-width-modulated counts ranging from 0 to 255. Always set the printer to a count of 51 or more counts when the extruder is heated up or ~~you are expecting~~ it to heat up.		Do not let the extruder heat up without a powered fan. The recommended fan setting is always above 20%. The printer gives fan commands in pulse-width-modulated counts ranging from 0 to 255. Always set the printer to a count of 51 or more counts when the extruder is heated up or it is expected to heat up.

	== Configuration ==		== Configuration ==

Blu at 20:00, 10 September 2018

2018-09-10T20:00:54Z

← Older revision		Revision as of 20:00, 10 September 2018
Line 24:		Line 24:
	== History ==		== History ==
	=== Head clogs ===		=== Head clogs ===
	The printer has been clogged at least five times. Every clog was because of incorrect heat application and has required ~~long-term~~ repairs.		The printer has been clogged at least five times. Every clog was because of incorrect heat application and has required specialty repairs.

Blu at 20:00, 10 September 2018

2018-09-10T20:00:21Z

← Older revision		Revision as of 20:00, 10 September 2018
Line 1:		Line 1:
	'''BLu Delta''' is a RepRap Kossel made by Brandon Lu.		'''BLu Delta''' is a RepRap Kossel made by Brandon Lu.

			== General Advice and Precautions ==
			It is by no means safe to operate this delta if the user wishes to consider himself a sane and rational human being.

			Operating this delta would create a situation in which the user ceases to be a sane and rational human being. The user may become a robot. Or you may lose your sanity.

			Either way, ask before using. The last time somebody used without asking, the extruder was clogged and needed to be unclogged through a two-hour process.

			=== Precautions ===
			Do not let the extruder heat up without a powered fan. The recommended fan setting is always above 20%. The printer gives fan commands in pulse-width-modulated counts ranging from 0 to 255. Always set the printer to a count of 51 or more counts when the extruder is heated up or you are expecting it to heat up.

			== Configuration ==
			TODO

			=== Slic3r ===
			TODO

			=== Cura ===
			TODO

			== Materials ==

			== History ==
			=== Head clogs ===
			The printer has been clogged at least five times. Every clog was because of incorrect heat application and has required long-term repairs.

KevinYang: KevinYang moved page BLu Delta to BLu Delta 3D Printer over redirect: Consistency with [tool model][tool type]

2018-09-10T00:21:08Z

KevinYang moved page BLu Delta to BLu Delta 3D Printer over redirect: Consistency with [tool model][tool type]

← Older revision	Revision as of 00:21, 10 September 2018
(No difference)

KevinYang: KevinYang moved page BLu Delta 3D Printer to BLu Delta

2018-09-09T23:25:43Z

KevinYang moved page BLu Delta 3D Printer to BLu Delta

← Older revision	Revision as of 23:25, 9 September 2018
(No difference)

KevinYang: Created page.

2018-09-09T23:24:55Z

Created page.

New page

'''BLu Delta''' is a RepRap Kossel made by Brandon Lu.